Is it in stock? If you can add it to cart, yes, in stock. Out of stock cannot be ordered
Free UK Shipping on all orders over £50
Flexible Payment options with Klarna & LayBuy
Need help? Fast Reply Email or call us: 0843 5328462

Hawke Tactical Mounts

Hawke Tactical Mounts 1" 2pc 9-11mm Dovetail MEDIUM Scope Mount Rings 24101

Hawke Tactical Mounts 1" 2pc 9-11mm Dovetail MEDIUM Scope Mount Rings 24101

£36.95 £30.79 (ex. VAT)
Stock Status: In Stock
Medium - 12mm base to ring bottom. For 1" tube scopes on 9-11mm dovetail. Maximum. Max scope outer case diameter 48mm
You Will Earn 36 points with this purchase

Make 6 weekly payments of £6.16.

Interest free. Learn More

Super strong and robust mounts

Triple torx screws to hold your scope firmly in place
Recoil Pin Stop
Rail 9-11mm
Internal cushion tape prevents marking and damage
High grade aluminium anodized in matte black

Configuration: 2 Piece
Ring Size (Diameter): 1″ / 25.4mm
Height: Medium (low medium)
Rail: 9-11mm
Fixings (Top Cap): Triple Torx Screw
Fixings (Rail): Double Hex Screw
Internal Cushion: YES
Retractable 'Recoil Stop' Pin: YES
Height: 43mm / 1.7″
Weight: 120g / 4.2oz

Fitting guidelines and clearance considerations

These mounts are for 9-11mm dovetail rails as typically found on air rifles and rimfire.

They are for 1 inch / 25.4mm scope tubes

They are an "on the low side" medium profile with 12mm measured from base of mount to base of ring (Saddle) - This is a critical dimension when calculating clearance over the rifle body.

Calculating scope to rifle body clearance

The way you calculate the clearance is by halving the overall OUTSIDE diameter of your rifle scopes objective lens and then deducting half the rifle scopes body tube diameter.

For scopes with a 1" diameter body tube diameter this would mean deducting 12.7mm and 15mm for scopes with a 30mm diameter body tube.

Note we say OUTSIDE diameter - this means NOT the lens diameter, you need to measure the whole outer casing diameter.

The result gives you the minimum "saddle" dimension required - the measure from base of mount to bottom of the ring.


The amount the saddle dimension is greater than the figure you have calculated is the amount of clearance your scopes objective will be clear of your rifles body.  The saddle on these mounts is 12mm

Example -

  1. A 50mm objective lens scope is measured and found to have an outer case measurement of 57mm.
  2. 57 divided by 2 = 28.5.
  3. 1" scope so deduct 12.7mm = 15.8mm
  4. So the mount must have a saddle measure (base of mount to bottom of the ring) greater than 15.8mm or else it will ground out on the rifle body.
  5. So with 12mm these are too short by 3.8mm unless the base is raised in some way. Go up to High profile if the base is flat

Calculating your rifle scopes clearance in this way does assume your dovetail or base is not raised above or below your rifles barrel. Note some rifles with high or adjustable cheek pieces may require higher scope mounts or risers so that your eye is in line with the rifle scope and your head is kept in an upright comfortable position.

  • EAN:
    5054492241019
  • MPN:
    24 101
  • Height:
    12mm base to ring bottom
  • Brand:
    Hawke
  • Product Code:
    NW2156
  • Weight:
    0.18kg
Not yet reviewed
Write an online review and share your thoughts with other shoppers!
Be the first to review this product