Flexible Payment options with Klarna, LayBuy and Paypal

Leapers Steel Rings

Leapers UTG Steel Picatinny Rifle Scope Mount Rings - 30mm HIGH RSW3224

Leapers UTG Steel Picatinny Rifle Scope Mount Rings - 30mm HIGH RSW3224
Leapers UTG Steel Picatinny Rifle Scope Mount Rings - 30mm HIGH RSW3224
Leapers UTG Steel Picatinny Rifle Scope Mount Rings - 30mm HIGH RSW3224
Leapers UTG Steel Picatinny Rifle Scope Mount Rings - 30mm HIGH RSW3224
Leapers UTG Steel Picatinny Rifle Scope Mount Rings - 30mm HIGH RSW3224

Leapers UTG Steel Picatinny Rifle Scope Mount Rings - 30mm HIGH RSW3224

£39.95 £33.29 (ex. VAT)
Stock Status: Sold Out
22mm base to bottom of ring "Saddle" and 37mm center height. Suit scopes with UPTO maximum 73mm OUTER objective diameter
You Will Earn 39 points with this purchase
Sorry, this item is out of stock. Enter your email to get a back in stock alert
Laybuy

Make 6 weekly payments of £6.66.

Interest free. Learn More

PayPal Checkout
Leapers UTG Steel Weaver/Picatinny Rifle Scope Mount Rings - 30mm ring diameter, HIGH profile, model code RSW3224
 

Pair - 2 rings supplied
 

Upper and lower ring portions precision machined from one solid block of steel to strict tolerances for optimal fit

Heat treated QPQ nitride matte black finish for strength and added weather and wear resistance

Progressively machined for a precise inner ring diameter to achieve optimal tube alignment; grooved inner surface guarantees tube retention

Radiused edges and corners prevent snagging, scratching, or tearing of other gear and give easy access to scope windage and elevation turrets

Locking Torx screws and square-shaped integral recoil stop for a secure zero hold

2 piece ring set, each equipped with 4 top Torx screws; mounting base designed to fit on MIL-STD-1913 rail platform

Includes a T15 Torx wrench for easy fitting



30mm Tube -

  • Ring is 30mm diameter.
  • To suit scopes with 30mm diameter tubes.


High Profile Height -

  • 22mm base to bottom of ring "Saddle" and 37mm center height. 
  • Suit scopes with UPTO maximum 73mm OUTER objective diameter i.e., not the actual lens size.
  • In practice this means just about any large scope.
  • This is down to the user to determine we can only give broad guidelines.
  • See scope clearance guide at bottom of page.


 

Calculating scope to rifle body clearance

The way you calculate the clearance is by halving the overall OUTSIDE diameter of your rifle scopes objective lens and then deducting half the rifle scopes body tube diameter.

For scopes with a 1" diameter body tube diameter this would mean deducting 12.7mm and 15mm for scopes with a 30mm diameter body tube.

Note we say OUTSIDE diameter - this means NOT the lens diameter, you need to measure the whole outer casing diameter.

The result gives you the minimum "saddle" dimension required - the measure from base of mount to bottom of the ring - the 'C' dimension that is shown above.

The amount the saddle dimension is greater than the figure you have calculated is the amount of clearance your scopes objective will be clear of your rifles body.  The saddle on these mounts is -

Example -

  1. A 50mm objective lens scope is measured and found to have an outer case measurement of 64mm.
  2. 64 divided by 2 = 32
  3. 30mm scope so deduct 15mm = 17mm
  4. So the mount must have a saddle measure (base of mount to bottom of the ring) greater than 17mm or else it will ground out on the rifle body. Here we have 22mm so there will be 5mm clearance.

Calculating your rifle scopes clearance in this way does assume the base is basic flat, not raised above or below your rifles barrel. Note some rifles with high or adjustable cheek pieces may require higher scope mounts or risers so that your eye is in line with the rifle scope and your head is kept in an upright comfortable position.

Base fit - Weaver/Picatinny base - rails that look like the one pictured below (base rail NOT included). May vary in length and be 2 smaller sections on some rifles. If you have a different base type, such as 11mm dovetail you can still use these mounts but will need to get an adapter base. Contact us with rifle make/model type for advice. We can also help with picatinny adapter bases for rifles such as Tikka, SAKO, CZ, Ruger, Remington, Howa, Weatherby, Marlin etc. See our selection of many picatinny adapter bases in the ebay shop section: Bases and Adapters


  • EAN:
    4717385552623
  • MPN:
    RSW3224
  • Height:
    22mm saddle
  • Brand:
    Leapers UTG
  • Product Code:
    NW2046
  • Weight:
    0.33kg
product review overlay image

Customer reviews

No reviews left yet
Write a review

No reviews have been left for this product, be the first to leave a review